Bayport Acrylic Working Demonstrators

"See through” acrylic training models: pumps, separators, boilers, and more!
Three Phase Separator  (3PS)
Acrylic Centrifuge Demonstration Unit  (CDT)
Acrylic Cooling Tower (CT-2)
Distillation Tower (DTT-5)
Floating Roof Tank (FRT)
U-Tube Circulation Trainer with Backwash (HECT-2)
Lubrication Training Unit (LUBE)
Pump Demonstration Training Model Custom (PDTM-2C)
Pump Demonstration Training Model (PDTM-2)
Acrylic Vacuum Trainer (VT)
Waste Water Training Unit (WWT)

This line of demonstrators are great for teaching your students the technical knowledge they need to success in the Oil and Gas industry. This list represents only sum of the products available. Customized acrylic working demonstrators are available upon request.

Acrylic Centrifuge Demonstration Unit (CDT)

This acrylic model was designed and manufactured for the purpose of demonstrating separation of liquids from solids by means of centrifugal force. Both the inner and outer ‘tubs’ are see through acrylic and allow full visibility of the process.

Acrylic Cooling Tower (CT-2)

Oil Refineries and Petrochemical plants use water to cool down the high temperatures that are generated by the particular process they use. This model is made of acrylic to allow full view of the water flow through the tower. This table top working model has an induction fan, circulation pump and tank.

Acrylic Distillation Tower (DTT-5)

This working model is an impressive and dynamic educational piece of equipment! It dramatically demonstrates the operation of a column using water and air. The models simulation is designed to show the basic process of distillation. Liquid traveling downward comes in contact with the vapors (gas bubbles) traveling upward, thus allowing the cooler liquid to condense any heavy compounds out of the lighter vapor stream.

Acrylic Heat Exchanger Circulation Trainer with Backwash (HECT-2)

Table top working model has two (2) circulation pumps and two (2) supply tanks for demonstration. Different colored water streams will be circulated through the shell side and through the tube side to simulate the working of a real heat exchanger.

Lubrication Training Unit (LUBE)

The Lubrication trainer is an acrylic bearing housing showing three of the most common methods of using a static pool (reservoir) to lubricate bearings. The unit is equipped with a variable speed motor, which allows the shaft to run slowly and at operating speeds. This allows the student to observe the lubrication process as well as rotating equipment such as the shaft and coupling.

Pump Demonstration Working Model (PDTM-2)

This “see through” training model has many features that can be used to train operators on the mechanical workings of a centrifugal pump. By manipulating the flow with suction and discharge valves and adjusting RPM’s this model can demonstrate cavitation and other pump and flow phenomena. Our Pump Demonstration Model is a very popular tool for a site and sound concept of these workings, which cannot be experienced in the field or with drawings or computer simulations.

Three Phase Separator (3PS)

Bayport has designed and built the 3PS Three Phase Separator to simulate process specific phenomena associated with the separation of gasses and fluids typically found in a crude oil production stream. This process trainer is a self contained unit which continuously mixes air, water, and a hydrocarbon based fluid which then flows into a series of ‘see through’ vessels where gravity separation takes place. The liquid components are returned to individual storage tanks prior to reblending, and the air is discharged to atmosphere. The trainer is equipped with process measurement devices and is operated from an integral control panel.

Acrylic Vacuum Trainer (VT)

This acrylic model vividly demonstrates the effect of atmospheric pressure variations on fluids and gasses. A good example is the boiling temperature of water.

Waste Water Training Unit (WWT)

This unit is designed to provide maintenance and operations personnel associated with Waste Water Treatment Facilities a first hand look at the workings of and the various methods of modern waste water treatment.

Other Acrylic Working Demonstrators:

  • Gas Lift Process Trainer (GLPT)
  • Lube Mist Trainer (LMT)
  • Charcoal Filter Trainer (CFT)
  • Floating Roof Tank Demonstration Model (FRT)
  • Custom Dual Pump Demonstration Model (PDTM-2C)

This list represents only a few of the products available. Customized acrylic working demonstrators are available upon request.

Bayport

Bayport Training & Technical is dedicated to providing specialized services and educational or industrial tools aimed at promoting a true “hands-on” teaching concept. The variety of cutaways, demonstrators and models are conceived and orchestrated through a client driven needs analysis program.

Mission Statement: To continuously work to achieve and repeatedly prove Bayport’s focus on existing and new technologies, quality and value in our products and services, through never ending diligence and dedication in providing unique tools, experienced personnel and contribution to our field of endeavor.

Visit Bayport Technical