Sight glass tubes at inlet and outlet of evaporator and condenser constructed of explosion proof, tie-bolt design, stainless steel drip pans with drains located under each evaporator and condenser, uses popular, brand name components, color-coded valves, gauges and hand valves to bypass various components and change from cooling to heating (heat pump operation), conditions of refrigerant and oil can be observed under various methods of operation...
Committed to Quality Education: iConnect's goal is to provide top quality trainers at reasonable prices that fit our customers’ precise needs.
Before going into the field, technicians need to understand each heating and cooling systems. iConnect Training systems are used to teach HVAC/R students the skills required for safe and efficient operation of each kind of system used in the industry. iConnect Training manufacturers high-quality training units for education which are used in high schools, technical colleges, government facilities and other educational settings worldwide.
iConnect Training provides a line of sophisticated training units that greatly aide in the teaching of Heating, Ventiliation, Air Conditioning and Refrigeration.
iConnect training units represent a variety of subjects in the heating, refrigeration and air conditioning. The units demonstrate a variety of skills ranging from simple concepts to advanced troubleshooting and servicing techniques. iConnect can also design and build custom trainers for your specifications and needs.
This training unit (TU-100) demonstrates domestic refrigerator and freezers, self-contained air conditioning units and reverse cycle or heat pump systems.Item Number:TU-100
HVAC Trainer for forced air and hydronic heating systems featuring featuring full-sized, completely operational componentsItem Number:TU-208
The forced air and hydronic heating trainer provides demonstration and service practice with forced air and hydronic heating systems, including hot water heating systems. All components are full size, completely operational and are standard brands of equipment.
This commercial refrigeration trainer is an advanced unit used to train students in commercial refrigeration and air conditioning systems.Item Number:TU-105
Sight glass tubes at inlet and outlet of evaporator and condenser constructed of explosion proof, tie-bolt design, cut-out and by-pass valves, hand valves allow malfunctions to be simulated, many control changes are possible, combination low pressure control and high pressure cut-out, thermostatic control with an adjustable range of –30°F to 100°F, 2 solenoid liquid line valves...
The double evaporator simulates a (TU-101) dual evaporator system application that demonstrates basic principles and provides service experience.Item Number:TU-101
Companion to the Motors, Controls and Circuit Trainer (Model TU-501). Designed for the student that has a working knowledge of the theory of refrigeration. Using this trainer, students are asked to design a system to match specifications of a particular situation. Instruction kit and experiment manual provide set-up and assembly directions.
This trainer is perfect for students to learn the basics of electric heat control systems.Item Number:TU-302
Complete set of operating controls of an electric furnace, wired 3 element furnace circuit, simulated heater elements operation shown by signal lamps, Klixon limit switch, fusible link safety device, thermostat, transformer, fan delay control, board designed for use on a bench or table...
This refrigeration demonstrator (TU-420) uses the 4 main parts of the refrigeration system that demonstrate basic refrigeration principles.Item Number:TU-420
This refrigeration demonstrator uses the 4 main parts of the refrigeration system (condenser, compressor, evaporator and control device) that demonstrate basic refrigeration principles. The components then work together to cool a small enclosed refrigerator compartment fully featured with an electronic temperature control device.
The control board contains a complete set of electrical controls of a furnace, with air conditioning, to demonstrate basic principles and provide electrical service experience.Item Number:TU-502
All the components of the Gas Fired Heating Control Board (TU-502) trainer are panel mounted. It is equipped for both thermocouple and thermopile systems. Signal lamps show simulated operation of burner valves, circulating fan air and air conditioning compressor.
The Industrial Refrigeration Trainer enables students to learn principles of commercial and industrial refrigeration systems.Item Number:TU-155
The Industrial Refrigeration Trainer (TU-155) is a self-contained freestanding unit with extra storage space below. This trainer is perfect for teaching students the principles of commercial and industrial refrigeration systems.
This training unit demonstrates basic refrigeration and air conditioning principles in a compact size, perfect for in the classroom or mobile training.Item Number:TU-805
Training Curriculum, Workbooks, & Certification Coming Soon:
Curriculum will be organized with sessions for addressing specific competencies and student learning outcomes. The package of training resources will include lecture notes, PowerPoint presentations, instructional videos, and lab exercises. Students will be able to demonstrate knowledge of the refrigeration cycle and complete iManifold® certification using the TU-805 Trainer and the included iConnect® System Analyzer kit.
Designed for the student with a working knowledge of the theory of refrigeration electrical control systems. Using this trainer, students are required to design a system to match specifications of a particular situation.Item Number:TU-501
Components are quickly mounted on the backboard using wing nuts for maximum flexibility in arranging components. Connections between components are wired by the students. (Mounting hardware must be purchased locally).